Talk:Data signaling rate

This article is within the scope of WikiProject Measurement, a project which is currently considered to be defunct.MeasurementWikipedia:WikiProject MeasurementTemplate:WikiProject MeasurementMeasurement

Telecommunications Mid‑importance

	Telecommunication portal This article is within the scope of WikiProject Telecommunications, a collaborative effort to improve the coverage of Telecommunications on Wikipedia. If you would like to participate, please visit the project page, where you can join the discussion and see a list of open tasks.TelecommunicationsWikipedia:WikiProject TelecommunicationsTemplate:WikiProject TelecommunicationsTelecommunications
Mid	This article has been rated as Mid-importance on the project's importance scale.

Merging

Latest comment: 12 years ago5 comments4 people in discussion

The following discussion is closed. Please do not modify it. Subsequent comments should be made in a new section. A summary of the conclusions reached follows.

The result of this discussion was page merged D O N D E groovily Talk to me 02:41, 18 March 2012 (UTC)Reply

According to this and a few other sources: "The bit rate is not to be confused with the data signaling rate which measures the rate of signal elements being transmitted." —Teknic^T-M-C 13:04, 20 Jun 2005 (UTC)

So they are referring to the difference between the actual content being sent and the wrappers and filler required to send it? Both are referred to by the term "bit rate", so this should at least be clarified, and probably merged into bit rate, since they are such similar ideas. Likewise for data transfer rate. - Omegatron 13:40, Jun 20, 2005 (UTC)

I'm no expert, but I think this article is just wrong. The signaling rate references a lower level than bits and has nothing to do with wrappers or headers. With a modem, for example, each "signal" can be one of a number of possible "conditions". If there are four possible conditions, then each signal can transmit two bits of information (00, 01, 10, or 11), so in this example the bit rate would be twice the signaling rate. Check out baud for more info. The article could use a rewrite, but I'm not familiar enough with these waters to just dive in. Regarding data transfer rate, I mentioned this on the talk page, but "transfer rate" can refer to the rate of anything, like packets/sec or characters/sec, not just bits, so it should not be merged with bit rate either. I agree that these three terms may be similar, but I can't imagine any possible benefit in merging them, or any other "similar" topics for that matter. —Teknic^T-M-C 17:32, 21 Jun 2005 (UTC)

Bits per second seems to be just as nebulous a concept. "Note that because of advancing technology, the actual bitrates used by some of the compared-to devices is significantly higher." "Bits per second" can refer to a data rate, a compressed data rate, a compressed data rate with extra things like bit stuffing added, etc.

These stubs about similar ideas should be merged into one article to clarify the differences between them. My opinion. - Omegatron 18:23, Jun 21, 2005 (UTC)

Teknic, I think your understanding is correct -- the lower-level "signaling rate" you mention is discussed in the symbol rate article; the higher-level "transfer rate" you mention is discussed at goodput. However, it seems clear to me that the definitions currently on this "data signaling rate" describe exactly the same thing as the "raw bitrate" in the bitrate article -- the theoretical maximum rate (in bits per second) resulting from the symbol rate times the maximum number of bits per symbol. Well, except for definition 5, which describes symbol rate alone. I agree with Omegatron that articles about very similar ideas should be merged, so I'm slapping the merge tag on the articles "data signaling rate" and "bitrate". --75.41.34.231 03:18, 18 May 2007 (UTC)Reply

I am removing the merge tag on this page as the merge tag has been removed on the article page. In addition, the "Talk:bitrate" page was deleted on August 12, 2007 as an necessary redirect so there is no page to merge into. --Alvin Seville (talk) 13:26, 5 April 2009 (UTC)Reply

Merge Data signaling rate and Maximum user signaling rate (renewing discussion)

Should Data signaling rate and Maximum user signaling rate be merged? Please comment here D O N D E groovily Talk to me 02:10, 12 March 2012 (UTC)Reply

Based on the material in the article Maximum user signaling rate, it seems reasonable to merge this article to Data signaling rate. Also, the references in the former article should be improved. Isheden (talk) 11:32, 13 March 2012 (UTC)Reply

The discussion above is closed. Please do not modify it. Subsequent comments should be made on the appropriate discussion page. No further edits should be made to this discussion.

Add topic