Wood carving

• Chip carving
• Relief carving
• Scandinavian flat-plane
• Lovespoon
• Treen
• Whittling
• Chainsaw carving
• Florentine carving

Pattern, Blocking, Detailing, Surfacing, and Smoothening

•  
  Carving knives
•  
  Carving knife used to round a corner of a piece of wood
•  
  V-Tool used to part lines and cut V-shaped channels

The nature of the wood being carved limits the scope of the carver in that wood is not equally strong in all directions: it is an anisotropic material. The direction in which wood is strongest is called "grain" (grain may be straight, interlocked, wavy or fiddleback, etc.). It is smart to arrange the more delicate parts of a design along the grain instead of across it.^[3] Often, however, a "line of best fit" is instead employed, since a design may have multiple weak points in different directions, or orientation of these along the grain would necessitate carving detail on end grain, (which is considerably more difficult). Carving blanks are also sometimes assembled, as with carousel horses, out of many smaller boards, and in this way, one can orient different areas of a carving in the most logical way, both for the carving process and for durability. Less commonly, this same principle is used in solid pieces of wood, where the fork of two branches is utilized for its divergent grain, or a branch off of a larger log is carved into a beak (this was the technique employed for traditional Welsh shepherd's crooks, and some Native American adze handles). The failure to appreciate these primary rules may constantly be seen in damaged work, when it will be noticed that, whereas tendrils, tips of birds beaks, etc., arranged across the grain have been broken away, similar details designed more in harmony with the growth of the wood and not too deeply undercut remain intact.^[3]

Probably the two most common woods used for carving^[4] in North America are basswood (aka tilia or lime) and tupelo; both are hardwoods that are relatively easy to work with. Chestnut, butternut, oak, American walnut, mahogany and teak are also very good woods; while for fine work Italian walnut, sycamore maple, apple, pear, box or plum, are usually chosen.^[3] Decoration that is to be painted and of not too delicate a nature is often carved in pine,^[3] which is relatively soft and inexpensive.^[5]

A wood carver begins a new carving by selecting a chunk of wood the approximate size and shape of the figure he or she wishes to create or if the carving is to be large, several pieces of wood may be laminated together to create the required size. The type of wood is important. Hardwoods are more difficult to shape but have greater luster and longevity. Softer woods may be easier to carve but are more prone to damage. Any wood can be carved but they all have different qualities and characteristics. The choice will depend on the requirements of carving being done: for example, a detailed figure would need a wood with a fine grain and very little figure as a strong figure can interfere with 'reading' fine detail.

Once the sculptor has selected their wood, he or she begins a general shaping process using gouges of various sizes. The gouge is a curved blade that can remove large portions of wood smoothly. For harder woods, the sculptor may use gouges sharpened with stronger bevels, about 35 degrees, and a mallet similar to a stone carver's. The terms gouge and chisel are open to confusion. Correctly, a gouge is a tool with a curved cross-section and a chisel is a tool with a flat cross-section. However, professional carvers tend to refer to them all as 'chisels'. Smaller sculptures may require the woodcarver to use a knife, and larger pieces might require the use of a saw. No matter what wood is selected or tool used, the wood sculptor must always carve either across or with the grain of the wood, never against the grain.

Once the general shape is made, the carver may use a variety of tools for creating details. For example, a "veiner" or "fluter" can be used to make deep gouges into the surface, or a "v-tool" for making fine lines or decorative cuts. Once the finer details have been added, the woodcarver finishes the surface. The method chosen depends on the required quality of the surface finish. The texture left by shallow gouges gives 'life' to the carving's surface and many carvers prefer this 'tooled' finish. If a completely smooth surface is required general smoothing can be done with tools such as "rasps," which are flat-bladed tools with a surface of pointed teeth. "Rifflers" are similar to rasps, but smaller, usually double-ended, and of various shapes for working in folds or crevasses. The finer polishing is done with abrasive paper. Large grained paper with a rougher surface is used first, with the sculptor then using finer grained paper that can make the surface of the sculpture slick to the touch.

After the carving and finishing is completed, the artist may seal & colour the wood with a variety of natural oils, such as walnut or linseed oil which protects the wood from dirt and moisture. Oil also imparts a sheen to the wood which, by reflecting light, helps the observer 'read' the form. Carvers seldom use gloss varnish as it creates too shiny a surface, which reflects so much light it can confuse the form; carvers refer to this as 'the toffee apple effect'. Objects made of wood are frequently finished with a layer of wax, which protects the wood and gives a soft lustrous sheen. A wax finish (e.g., shoe polish) is comparatively fragile though and only suitable for indoor carvings.

•  
  A wooden Bodhisattva from the Song dynasty (960–1279)
•  
  Japanese wooden mask depicting demon.
•  
  Wooden portrait of Minamoto no Yoritomo, 13-14th century
•  
  Balinese wood carving from Indonesia, depicting Vishnu mounting Garuda
•  
  Index of American Design, Federal Art Project, Frank McEntee, artist, watercolor
•  
  Tilman Riemenschneider's Saint Barbara from Germany
•  
  Yombe-sculpture, 19th century
•  
  in Festac Town, Lagos, Nigeria
•  
  Wooden Krishna, India
•  
  Carved gallant genre scene with figurines from Val Gardena, 18th century
•  
  Carving of a unicorn by G&H Studios, Somerset, England
•  
  c. 1940s, hobo by Carl Johan Trygg
•  
  The eponymous carving on the Urnes stave church is an example of the Urnes style, Norway
•  
  An angel on the front part of a confessional in a church as a metaphor of the seal of confession, Poland
•  
  Desay Madu Jhya (window) in Kathmandu, Nepal is a specimen of traditional Nepalese wood carving
•  
  Detail of the Last Supper from Tilman Riemenschneider's Altar of the Holy Blood, 1501–05, Rothenburg ob der Tauber, Germany
•  
  The Chevy Chase Sideboard by Gerrard Robinson. Often considered to be one of the finest carved furniture pieces of the 19th century and an icon of Victorian furniture.
•  
  Carved tree with reliefs of dinosaur and other animals, Laos
•  
  Carved wooden cranes
•  
  Finely carved wooden door in the Great Mosque of Kairouan, Tunisia
•  
  Carvings for sale on a beach
•  
  Noah's Ark with animals-Sunday toy- Index of American Design Federal Art Project
•  
  Old choir stalls. National Sculpture Museum in Valladolid
•  
  Pulpit in Church of St Peter and St Paul in Mechelen
•  
  A Székely gate in front of the Székely National Museum, in Sfântu Gheorghe, Romania
•  
  Wooden Female Figure from the Hunt Museum collection.
•  
  Porte Hugues Sambin, door of the old Parliament of Burgundy and the current court of appeal of Dijon (Côte-d'Or, France)

• List of woodcarvers
• Chainsaw carving
• History of wood carving
• Woodcut
• Woodturning
• Woodworking
• Wood carving in the Marquesas Islands
• Woodcarved Catholic saints in the Parish Church of Ortisei, northern Italy
• National Wood Carvers Association
• Woodcarving events:
  • Woodfest Wales
• Arborglyph, carvings made in the bark of living trees

•   This article incorporates public domain material from websites or documents of the National Archives and Records Administration.